We are continually updating our photos. 
Please check back again soon!

This Rossi Revolver was DuraCoated in the Diamond Plate Pattern.

The following 8 photos are the depiction of the restoration of a GAU-8 Avenger Weapons System from an A10 Warthog, commonly known as "The Tank Killer". This restored piece will be on display at the Museum of Aviation in Warner Robins.

Here is the complete weapons platform including the 7 barrels and the receiver.

This is the "Receiver" separated from the barrels.

This is the "Receiver" that has been restored with DuraCoat in the Parker color.  All the materials for this project were donated by
Lauer Custom Weaponry.

Gary Hadley with Oakridge Custom Finishing doing some final touch-ups on the weapons platform before it goes on display.

Looking down the mouth of total destruction!

Here is another picture after the receiver and barrels have been re-assembled.

Mossberg Shotgun with our "Free-hand Signature Camo Pattern"
(We can do this to your gun! Priced at about $220.00)

This M1 Garand, manufactured in 1953, was completely restored receiving new Parkerizing and a new walnut stock. Aside from not having the cartouches, the rifle is about as close to what it looked like when it was produced by Springfield. The TE on the barrel measured 1.5

The pink stock on this .22LR Cricket came from the factory.  
The purple DuraCoat on the barrel was custom mixed.  
This is the only Cricket like it in the world.

Here is a pair of Russian Baikal Over/Under Shotguns finished in our Custom Blue-Black DuraCoat finish. They are very nice and operate like a pair of new Singer Sewing Machines.

Here is a custom DuraCoated Bersa
This pistol has been finished to specifications for the
Women's Shooting Federation in Casper, Wyoming

Intratec Tec-DC9, 9MM Luger
DuraCoated in Leupold Dark Earth on Upper Receiver and Magazine
and AUG Green on Lower Receiver

Bushnell scope ready for Matte Black

Bushnell coated in Matte Black

This is a beautiful example of a custom pattern applied to a great shooting Savage Tactical rifle in .308. This one shoots cosistent 1/2" moa at 100 yards. Greg did a great job on this piece!

Flip side of the Savage Tactical. 

This is a short .223 Wylde barrel that was prepped and coated with HK Black DuraHeat.

This is a Colt Ar-15 that was meticulously prepared by our client and coated in a non-durable finish. The finish turned very dirty and began slipping after approximately 250 rounds. This weapon will be disassembled, degreased and blasted to remove both the custom finish and the original finish. Photos 1,2 and 3

The Colt AR-15 disassembled and blasted removing all finishes. The next step for this weapon is Parkerizing. Photo 4

The Colt AR-15 has now been Parkerized and is ready for the High Temperature Coating of DuraHeat. This weapon is suppressed and generates a lot of heat! Photo 5

The Colt has now been comletely finished in HK DuraHeat inside and out and reassembled. The finish is more subdued than is shown here due to the camera flash and a light coat of gun oil. Photos 5 & 6

Winchester 94 with very little bluing and rust. Photo 1

Here is the Winchester 94 degreased and blasted clean. Photo 2

The same Winchester 94 Parkerized and ready for the field. Photo 3

Advanced Armaments 7.62 Suppressor as recieved from our client.

Here is the suppressor after removing the original finish.

The suppressor has recieved a new coat of DuraHeat in Wildlife Tan.

TTU-30 in Combact Black

TTU-30 in Combat Black

HOWA Model 1500 .308 sitting on a Special Ops Knoxx Stock and topped with a Trijicon ACOG. The suppressor below sits on the end of the barrel of this one. This piece will be finished in some light camo colors.